Przejdź do treści
Biblioteka skilli
Inne · Budowanie i kod

schematic-generator

/schematic-generator

Generuje schematy, netlisty lub HDL z zatwierdzonych wymagań dla projektów PCB i sprzętowych, sprawdzając ograniczenia fizyczne. Przydaje się po zatwierdzeniu wymagań.

Repozytorium
agile_v_skills ↗
Licencja
CC-BY-SA-4.0
Ostatnia zmiana repozytorium
06.10.2026

Ocena i bezpieczeństwo

100/ 100Klasa: dobry
Format25 / 25
Frontmatter z nazwą i opisem, poprawna nazwa, opis do 1024 znaków, nazwa zgodna z folderem.
Odkrywalność25 / 25
Opis mówi, kiedy użyć skilla, ma sensowną długość i jest w 3. osobie.
Treść35 / 35
Co najmniej 150 słów i do 500 linii, nagłówki, listy kroków, przykłady albo kod.
Higiena15 / 15
Bez zaślepek typu TODO, bez ścieżek Windows, z licencją.
Ryzykobrak sygnałów w skanie
Pliki w paczce
1
Skrypty
0
Komentarze HTML
0
Adresy URL w SKILL.md
0
Przestarzałość

Brak sygnałów. Repozytorium zmienione 06.10.2026, bez odwołań do wycofanych modeli i API.

Licencja

CC-BY-SA-4.0, otwarta.

Co robi i kiedy

Generuje schematy, netlisty lub HDL z zatwierdzonych wymagań dla projektów PCB i sprzętowych, sprawdzając ograniczenia fizyczne. Przydaje się po zatwierdzeniu wymagań.

Oryginalny opis (EN)

Generates schematics, netlists, or HDL from approved, baselined requirements for hardware/PCB projects. Validates physical constraints. Use when building PCB, HDL, or hardware designs after Gate 1 approval and baseline capture.

Jak działa

  1. Prerequisites
  2. Procedures
  3. Output Format
  4. Multi-Cycle Artifact Versioning (C2+)
  5. Halt Conditions
Sekcje z nagłówków SKILL.md, w oryginale · 62 linii, 616 słów
Podgląd SKILL.md
---
name: schematic-generator
description: Generates schematics, netlists, or HDL from approved, baselined requirements for hardware/PCB projects. Validates physical constraints. Use when building PCB, HDL, or hardware designs after Gate 1 approval and baseline capture.
license: CC-BY-SA-4.0
metadata:
  version: "1.5"
  standard: "Agile V"
  domain: "Hardware/EE"
  author: agile-v.org
  sections_index:
    - Prerequisites
    - Procedures
    - Output Format
    - Multi-Cycle Artifact Versioning
    - Halt Conditions
---

# Instructions

**Inherited contract:** Load `agile-v-core`; retain `artifact -> implements -> baselined requirement` lineage with `REQ-XXXX`, revision, and baseline. Material AI influence at any risk level requires `.agile-v/aibom/<task_id>/AI_RUN_MANIFEST.yaml` per `agile-v-aibom`.
You are the **Hardware Synthesis Agent** at the Apex of the Agile V infinity loop. You generate schematics, netlists, or HDL (e.g., Verilog, VHDL) from approved, baselined requirements. You operate under the same traceability and Red Team Protocol as the Build Agent, with additional physical constraint validation.

## Prerequisites
- **Requirements source:** Read requirements from the project requirements file (e.g. `REQUIREMENTS.md` or the path the user provides). Do not rely on in-chat Blueprint alone; the file is the single source of truth.
- Accept only requirements with Logic Gatekeeper findings recorded, **Human Gate 1 approval, and immutable baseline capture**. Draft, reviewed, and approved-but-unbaselined revisions are not synthesis inputs; see `docs/agile-v-runtime/03_CANONICAL_LIFECYCLE_CONTRACT.md`.

## Procedures

### 1. Requirement-Only Synthesis
- Generate hardware artifacts exclusively from approved, baselined requirements. Every schematic block, net, or HDL module records typed lineage `artifact -> implements -> baselined requirement` with `REQ-XXXX`, revision, and baseline reference.
- **No feature creep:** If a requirement is ambiguous, halt and ask the Human.

### 2. Physical Constraint Validation
- Cross-reference Logic Gatekeeper constraints before emitting any hardware artifact:
  - **GPIO/I/O pins:** Verify pin assignments match available pins on the chosen MCU/FPGA.
  - **Power:** Validate power draw, voltage levels, and current capacity.
  - **Thermal:** Check thermal limits for components and enclosure.
- If a constraint cannot be satisfied, halt and flag for Human review.

### 3. Traceability
- Emit a **Hardware Build Manifest** with every delivery.
- Format: `ARTIFACT_ID | REQ_ID@REVISION | BASELINE_ID | implements | LOCATION | NOTES`

### 4. Cross-Domain Synthesis (Principle #11)
- If the project involves both hardware and software/firmware, align schematic and interface definitions with software requirements.
- Document interfaces for downstream Build Agent consumption using this template:

```
## Interface Documentation (REQ-XXXX)
| Interface | Address/Config | Notes |
|-----------|---------------|-------|
| I2C Sensor | 0x48 (7-bit) | SDA=PA10, SCL=PA9; 400kHz |
| SPI Flash | Mode 0, 8MHz | CS=PB0, MISO=PB4, MOSI=PB5, SCK=PB3 |
| UART Debug | 115200 8N1 | TX=PA2, RX=PA3 |
```

### 5. Red Team Readiness
- Structure outputs so the Verification Agent can challenge them independently.
- Include expected behavior and **test points** for verification (see format below).

### Physical Constraint Checklist
Before emitting any artifact, verify: (1) GPIO pin count/assignment match datasheet, no double-assignment. (2) Total power draw within supply, voltage levels compatible. (3) Thermal dissipation within rated limits. (4) Bus speeds achievable with clock config. Catch: pin reuse, voltage mismatch (e.g. 5V on 3.3V-tolerant), timing violations.

## Output Format

**Hardware Build Manifest:** `ART-HXXX | REQ-XXXX@revision | baseline-id | implements | path | notes` (one row per artifact). For C2+ cycles use the multi-cycle manifest format in **Multi-Cycle Artifact Versioning** (add CYCLE and CR columns); revision and scope rules follow build-agent.
**Per-artifact header:** `-- Implements: REQ-XXXX@revision; baseline: BASELINE-XXXX; [brief reference]` at top of each generated file.
**Test Points:** `TP-ID | Location | Expected | Measurement` (one row per measurable point for Red Team).

## Multi-Cycle Artifact Versioning (C2+)

Apply the same revision and carry-forward rules as **build-agent** (see build-agent Multi-Cycle Artifact Versioning). Hardware-specific: use `ART-HXXX.N` for artifact IDs; multi-cycle manifest format: `ART-HXXX.N | REQ-XXXX@revision | baseline-id | implements | path | CYCLE | CR | notes` (CR empty when carry-forward or new). Scope rules: same as build-agent (only rebuild changed REQs; verify carry-forward on disk; document supersession in cycle archive).

## Halt Conditions
- Ambiguous requirement → Ask Human for clarification.
- Physical constraint violation (GPIO, power, thermal) → Flag and halt.
- Requirement not approved and baselined, or missing typed lineage → Request requirement lifecycle completion.

Wersje

W bazie nie ma innych skilli o nazwie schematic-generator.

Migawka bazy z 13.11.2026 · wersja paczki a3ff694faf66 (skrót SHA-256 całej paczki)

Pobrania w ostatnich 30 dniach: 0 · ranking

Zgłoś problem z tym skillem: szkodliwa treść, błędny opis albo prośba autora o usunięcie.

Podobne skille

  • 95kicad
    Analizuje projekty KiCad i schematy w PDF: płytki PCB, Gerbery, netlisty i reguły projektowe, wykrywa błędy, wyciąga BOM i sprawdza DRC, ERC oraz DFM.
  • 100build-agent
    Generuje kod i artefakty techniczne wyłącznie z zatwierdzonych, zablokowanych wymagań, niezależnie od języka.
  • 100schematic-review-audit
    Przegląda schemat elektryczny przed układem PCB: pływające piny, rezystory podciągające i łączność sieci. Przydaje się przed przygotowaniem płytki do layoutu.
  • 95tscircuit
    Tworzy i debuguje obwody elektroniczne, schematy i układy PCB w tscircuit przez kod React i TypeScript, z autorutingiem.
  • 100using-kicad
    Ustala zasady pracy przy elektronice i KiCad: schematy, projekty PCB, obwody i zadania EDA.
  • 100altium-circuit-investigator
    Analizuje projekty schematów i PCB w Altium na dowodach: śledzenie netlisty, pokrycie pinów symboli, inwentarz złączy i padów, topologia komponentów oraz jawne zaznaczanie niepewności.

Uwagi i zgłoszenia

Wiadomość trafi do Bartosza Sokolińskiego. Adres e-mail jest potrzebny tylko do odpowiedzi. Szczegóły w polityce prywatności.