held-object-geometry
/held-object-geometry
Ustala położenie końca, miejsca wejścia lub roboczej części trzymanego obiektu względem dłoni, gdy prześwit albo kontakt narzędzia zależą od pozycji ładunku.
- Autor
- Open-RUA ↗
- Repozytorium
- uni-robot-agent ↗
- Licencja
- MIT
- Ostatnia zmiana repozytorium
- 11.11.2026
Ocena i bezpieczeństwo
- Pliki w paczce
- 1
- Skrypty
- 0
- Komentarze HTML
- 0
- Adresy URL w SKILL.md
- 0
Brak sygnałów. Repozytorium zmienione 11.11.2026, bez odwołań do wycofanych modeli i API.
MIT, otwarta: można używać i zmieniać, z zachowaniem informacji o autorze.
Co robi i kiedy
Ustala położenie końca, miejsca wejścia lub roboczej części trzymanego obiektu względem dłoni, gdy prześwit albo kontakt narzędzia zależą od pozycji ładunku.
Oryginalny opis (EN)
Locate the bottom, entering end or working feature of a held object relative to the hand. Use when clearance, placement or tool contact depends on the load's actual pose.
Jak działa
- Preserve only geometry that remains valid
- Check both the moving shape and the receiver
- Case: the object is already aligned, but the hand looks rotated
Podgląd SKILL.md
--- name: held-object-geometry description: Locate the bottom, entering end or working feature of a held object relative to the hand. Use when clearance, placement or tool contact depends on the load's actual pose. --- # Plan with the held object's actual features Identify the feature needed for the next operation: the lowest edge for clearance, an entering end and axis for engagement, or a working surface for tool contact. Estimate its relation to the measured hand from a compatible observation. The finger center, mask median and object center are not interchangeable features. Use `general/gripper/grasp-geometry/SKILL.md` to keep the needed feature accessible. ## Preserve only geometry that remains valid A held object can hang tilted or offset even when the hand reaches its requested pose. Inspect its actual bottom, rim, long extent or working end rather than assuming the initial grasp centered it. After reorientation, transform the feature relationship with the new orientation and check that the grip did not shift; a world-axis offset cannot simply be reused after rotation. Slip, regrasp or support transfer invalidates the old hand-to-object relationship. Refresh the affected feature before precise contact. Reuse a confirmed relation through undisturbed motion; do not repeatedly measure the entire object. ## Check both the moving shape and the receiver Plan approach and withdrawal for the whole load and fingers, including edges below or beside the grasp. A hand above a rim does not establish clearance for the lowest corner. Localize the receiving opening or support again if it moved; an accurate held-object offset cannot compensate for a stale destination. Separate hand tracking, retention and effective contact. A working end following the hand establishes control of the tool, not its effect on the target. Use `general/gripper/contact-effect/SKILL.md` for that effect and `general/gripper/placement-and-engagement/SKILL.md` for the resulting relation. When fingers obscure the deciding feature, choose a useful view or a supported release and withdrawal if the operation permits it; an occluded mask can appear smaller or lower without the object having seated. ## Case: the object is already aligned, but the hand looks rotated The object's identifiable face and directed features already satisfy the required world orientation, although the grasp-site yaw is nonzero. Preserve that useful object orientation during transport when the route permits it. Zero grasp-site yaw is not an object-alignment objective; an unnecessary loaded turn can shift the grip and make the remaining route harder. Confirm alignment from distinguishing features, not bbox aspect ratio alone. If rotation is required, choose it from the measured hand-to-object relationship and available clearance, not an assumed centered grip. After slip, regrasp or an unexpected turn, refresh the affected relationship before using the old placement offset. When retention and geometry remain valid, reuse them and inspect the released result without repeating localization at each move. Before precise engagement, compare the actual working feature and its axis with the receiver, then account for the fingers' approach and withdrawal space. Do not translate a receiver coordinate directly into a gripper-center target without the supported hand-to-feature relationship. A tighter motion tolerance cannot repair an incorrect feature offset or stale held orientation.
Wersje
W bazie nie ma innych skilli o nazwie held-object-geometry.
Migawka bazy z 13.11.2026 · wersja paczki 872552581651 (skrót SHA-256 całej paczki)
Pobrania w ostatnich 30 dniach: 0 · ranking
Zgłoś problem z tym skillem: szkodliwa treść, błędny opis albo prośba autora o usunięcie.
Podobne skille
- 100placing-held-feature
Przesuwa trzymany obiekt tak, by wybrana cecha trafiła w punkt docelowy, na przykład pierścień na hak, wyliczając pozycję dłoni z aktualnej pozy obiektu w każdej rundzie. - 100planning-held-object-motion
Planuje fazy przenoszenia i dopasowania trzymanego sztywnego obiektu: podniesienie z zapasem, najmniejszą reorientację, tranzyt nad przyrządem oraz wsunięcie liniowe lub typowane zazębienie. - 100placement-and-engagement
Planuje i sprawdza podparcie, zamocowanie, zagnieżdżenie lub połączenie mechaniczne na podstawie widocznych cech obiektu i geometrii. - 95pose-targeting
Buduje cele pozy w narzędziach ruchu, z właściwą ramką pozycji i semantyką rotacji przy zmianie orientacji obiektu.